|
|
Spring Roller Specifications
|
 Minimum Width |
15" |
| Minimum Height |
24" |
| Maximum Width |
73"
|
| Maximum Height |
120" |
Continuous Loop Cord Specifications
|
| Minimum Width |
15" |
| Minimum Height |
24" |
| Maximum Width |
103"
|
| Maximum Height |
120" |
Railroad Specifications
|
| Maximum Fabric Width |
94" |
| Horizontal Seam |
Over 94" x 84" |
Installation Requirements:
|
| Minimum Inside Mount Depth |
2 1/4" |
| Minimum Inside Mount Depth (fully recessed) |
3" |
| Minimum Outside Mounting Surface |
2" |
| Inside Mount Deduction |
1/4" |
| Light Gap per Side |
9/16" |
Cassette Installation Requirements:
|
| Minimum Inside Mount Depth |
2 1/4" |
| Minimum Inside Mount Depth (fully recessed) |
4 1/8" |
| Minimum Outside Mounting Surface |
2" |
| Inside Mount Deduction |
1/4" |
| Light Gap per Side |
11/16" |
|
|
|
|
|
|
|
|
Warranty Information
|
|
LIFETIME LIMITED WARRANTY
Our Guarantee: Once you are satisfied with your new Phase II Blinds and the way it is installed in your home, Phase II guarantees your blinds will be free from defects due to faulty workmanship or materials for as long as the original purchaser owns the product, provided that the product was installed properly and in accordance with the installation instructions. The warranty is extended to the original purchaser only, in the original windows for which it was intended in residential properties only.Five Year Warranty: For the period of five years from the date of purchase, Phase II will repair or replace any slat which is defective.Our Obligation To You: For claims covered by the guarantee, Phase II will replace or repair any product, with like or similar parts, found to be defective as a result of faulty workmanship or materials, and excludes shipping cost, trip charges and labor cost for measuring and installation.Guarantee Limits: This guarantee does not apply to any Phase II blinds or parts thereof which fail due to accident, alterations, improper use, abuse, neglect, normal wear, nor color fading due to sunlight, direct exposure to salt air, failure to follow instructions for measuring, installing or operating the product. Slight warpage and variation in color and grain are normal and not considered defects.Any defect, malfunction or other failure of the product to conform to this limited guarantee will be remedied by Phase II solely in the manner provided in this guarantee.THIS LIMITED GUARANTEE DOES NOT COVER, AND IS INTENDED TO EXCLUDE, ANY ALL LIABILITY ON THE PART OF THE COMPANY, WHETHER UNDER THIS LIMITED GUARANTEE OR UNDER ANY GUARANTEE IMPLIED BY LAW, FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES FOR BREACH THEREOF EXCEPT AS EXPRESSLY PROVIDED ABOVE IN THIS LIMITED GUARANTEE, THE COMPANY HEREBY NEGATES AND DISCLAIMS ALL EXPRESS GUARANTEES.Notes: Some states do not allow the exclusion or limitations of incidental or consequential damages, so the foregoing limitation or exclusion regarding such damages may not apply to you. Also, this limited Guarantee gives specific legal rights, and you may also have other rights which vary from state to state.
|
| How To
Measure |
 |
Measuring
guidelines for Roller Shades |
Precise width and length measurements are critical. Fabric
width cannot be altered after the shading is fabricated.
Please use a metal tape measure for accuracy from home
to factory.
The headrail must be installed perfectly level and installed
evenly to ensure smooth operation. On an inside mount,
it is recommended that you check to see that the mounting
surface is level and consistent. If your soffit needs
to be leveled, this should be done before measuring.
|
Measuring
guidelines for Roller Shades |
Precise width and length measurements are critical. Fabric
width cannot be altered after the shading is fabricated.
Please use a metal tape measure for accuracy from home
to factory.
The headrail must be installed perfectly level and installed
evenly to ensure smooth operation. On an inside mount,
it is recommended that you check to see that the mounting
surface is level and consistent. If your soffit needs
to be leveled, this should be done before measuring.
INSIDE MOUNT
Mark order “Inside Mount”. Using a Metal Tape, Measure across the inside width of your window opening where the roller shade brackets will be installed to the nearest 1/8”. Factory will deduct 1/8” to ensure proper fit. Measurements should be taken within the window jamb. NOTE: If the middle and bottom measurement vary more than 1/2”, call before ordering. Be exact, the factory will make the necessary deductions to fit the window opening.
Measure the length of the window opening from the underside of the soffit to the surface of the window sill in two places - use the smallest of these two measurements.
Inside mount blinds are installed inside the window casing. Check to be sure your window opening is deep enough to accommodate the mounting hardware and headrail which is 3 1/2" for a flush mount. Call or e-mail us for specific details.
| Cassette
Headrail System/Loop Cord |
Standard
Spring Roller System |
Headrail
will measure ordered width less 3/16"
Fabric will measure ordered width less 1 1/8"
|
Headrail
roll will measure ordered width less 1/8"
Fabric will measure ordered width less 1 1/8"
|
OUTSIDE MOUNT
Measure the exact width and length of the area to be covered.
On the width, add at least 1" of overlap on each
side of the opening or window casing. Add a minimum of
3 1/2" - 4" length to allow for the headrail
or mounting brackets if you are mounting above the window
casing. Call or e-mail us for specific details.
Be sure to take into consideration any obstruction such
as window trim, molding, locks and window cranks.
| Cassette
Headrail System/Loop Cord |
Standard
Spring Roller System |
Headrail
will measure ordered width plus 3/16"
Fabric will measure ordered width less 1"
|
Headrail
will measure ordered width plus 3/16"
Fabric will measure ordered width less 1" - 1 1/8'
|
|
|
| Shipping
Fees |
UPS or FedEx Ground Shipping:
This applies to all orders under 94 inches in width or length shipping to an address in the contiguous 48 states of the U.S. If it travels by UPS or FedEx then shipping is FREE! Please call us for shipping quotes outside the covered area.
Oversize Products Shipping Fee:
If your package is 94 inches or over in width or length it will be shipped by common carrier (semi truck) from the nearest manufacturing facility to you. There will be a 90 dollar oversize shipping charge for any order with products that are 94 inches or more in width or length. This charge is per manufacturer. Meaning if you order two oversized products and they are from two different manufacturers (two different brands) there will be TWO charges for a total of 180 dollars in shipping. But, if you have more than one product over 94 inches that is from the same manufacturer you will only pay one oversize fee. The fee is per order, not per blind.
Excludes Plantation Shutters, which incur no additional shipping charges. |
© 2013 BlindsOnSale.com. All rights reserved.
| |
